Atmel AT89Sxxxx Series Min-Sys

INTRODUCTION

Now this is another kind of design but use a minimum system types using Atmel MCS51 S-series with ISP programming. So with this kind of board, the chip do not need to remove just programmed on board. Programed using ISP programming could be done directly through LPT parallel port. There are many programming software could be found on the internet. Some that I could find and much realiable eq.: AEC-ISP programmer, this kind is DOS version. Could be download at : AEC-Electronics. Also ISP programmer made by Asim Khan, could be download at : Asim Khan's ISP software, this kind is a windows version. Besides that there is software from Adam Dybkowsky which run both version of programmers. It could be found at : Adam's Home Page ISP PROG ATMEL89Sxx. Every programmers used its own ISP cable.

On Tauhid

Allah--ta`ala--has said: "I have not created jinn and
mankind except to serve Me . . . And to every people We sent a
prophet to convey to them that they ought to serve Allah and
avoid at-taghot. . . . Your Lord has decreed that you shall
serve none but Him, and show kindness to your parents . . .
Serve Allah and do not associate aught with Him . . . Come, let
me tell you what your Lord has forbidden you; namely, that you
do not associate aught with Him." (Qor'an 51:56, 16:36, 17:23,
4:36, 6:151-153)

Basic SR flipflops

Circuit Description

This circuit demonstrates the basic SR (for set-reset) flipflops built from NAND and NOR gates. The typical structure of both circuits are the feedback lines that connect the output of one gate back to the input of the other gate.

The behavior of both circuits is very similar; the most important feature is that the circuits are able to store information. Please play with the circuits and compare the simulation with the function (or state) tables on the right of the schematics.

In all normal states, the output of the two gates are inverse to each other, which means that a flipflop circuit can generate both the Q output value and the inverted NQ output value at no extra cost. Naturally, the so called forbidden states don't damage the circuit, but they should be avoided because in those states the outputs of the two gates are not complementary to each other.

Scanning 7-Segment

Since the output buffer of P1 can sink 20mA (each output pin, but maximum IOL for all outputs was limited at 80mA), thus we can use P1 to drive LED display directly. As shown in the circuit, Two common-anode 7-segment LEDs are connected to P1 with 180 Ohms current limiting resistor. Each segment of two LED are tied in parallel to P1. Q1 and Q2 are activated by logic low of P3.0 and P3.1, sourcing +5V to common anode pins. P3.4 read logic low if either S1 or S2 was pressed while scanning period have made.



download :

7-SEG.C

DC Power Supplay

Electronic devices should be powered by direct current supply DC (direct current) which is stable in order to work properly. The battery or batteries is a source of DC power supply is best. But for applications that require greater power supply, the source of the battery is not enough. Sources of power supply is a source of alternating AC (alternating current) from power plants. This requires a power supply device that can change the AC into DC current.



Rangkaian Power Supplay

Now it should not need another effort to make good pwer supplay you do not need to look for op-amps, transistors and other components, because these circuits are packaged into a single fixed voltage regulator IC. Are now widely recognized as a component of 78XX series fixed positive voltage regulator and the 79XX series is a voltage regulator to remain negative. Even these components are usually already equipped with current limiting (current limiter) and also limiting the temperature (thermal shutdown). This component is only three pins, and by adding some components alone can be a series of power supply regulation was good.


Now it should not need another effort to make good pwer supplay you do not need to look for op-amps, transistors and other components, because these circuits are packaged into a single fixed voltage regulator IC. Are now widely recognized as a component of 78XX series fixed positive voltage regulator and the 79XX series is a voltage regulator to remain negative. Even these components are usually already equipped with current limiting (current limiter) and also limiting the temperature (thermal shutdown). This component is only three pins, and by adding some components alone can be a series of power supply regulation was good.
It's just to note that the I C regulator circuit that can work, the input voltage must be greater than the output voltage regulator. Usually the difference voltage Vin to the recommended VM is in the component data sheet. Usage heat hink (Aluminum cooling) is recommended if these components are used to supply large currents. In the datas heet, these components can pass the maximum current reached 1 A.